; S-COM Sample 7330 Script file ; 5/4/2013, Dave Maciorowski, wa1jhk@ix.netcom.com ; ; Comments begin with a semi-colon and can be on the end ; of lines containing commands. ; ;---------------------------------- ; Message Defaults, Chapter 6 ;---------------------------------- ; ; Set Port-specific message defaults ; CW Tone Frequency ; MPW 06 20 0248 * ; 1500 Hz (default) ; CW Speed Select ; MPW 12 20 6 * ; 20 WPM (default) ;---------------------------------- ; DTMF, Chapter 7 ;---------------------------------- ; ; DTMF Decoders are dedicated to a specific Receiver. The configuration ; below configures only the DTMF Decoder for this port. ; QUICKSTART -- you will need to define the Access Mode for the Link Receiver DTMF Decoder. ; The default is Carrier Access. Set to 0 (Disable) if this port shouldn't enter commands. ; ; Access Mode ; MPW 57 2 1 * ; DTMF Decoder Access Mode - Carrier Access (default) ; Timing ; MPW 09 0208 0 * ; DTMF Anti-Falsing Timer, 0 Seconds (default) ; MPW 09 0204 500 * ; DTMF Interdigit Timer, 5.00 Seconds (default) ; MPW 63 0204 0 * ; DTMF Command Execution on Interdigit Timer Enable (disabled, default) ; MPW 63 0203 0 * ; DTMF End-Of-Transmission Command Execution Enable (disabled, default) ; MPW 63 0207 0 * ; DTMF 4th Digi5 Command Execution Enable (disabled, default) ; MPW 63 0205 0 * ; DTMF Disconnect Timer Enable (disabled, default) ; MPW 09 0207 500 * ; DTMF Disconnect Timer, 5.00 Seconds (default) ; Mute Hang Times. Note: Enables are set by Path, See Below ; MPW 09 0205 50 * ; DTMF Mute Hang Time, .50 Seconds 1st Digit (default) ; MPW 09 0206 50 * ; DTMF Mute Hang Time, .50 Seconds Other Digits (default) ; DTMF Cover Tone ; MPW 09 0219 0 * ; DTMF Cover Tone Interval, 0.00 seconds (disabled, default) ; MPW 31 0213 9910 56 71 64 14 14 * ; DTMF Cover Tone Message, dual beeps (default) ; Misc Macros ; MPW 26 0201 * ; DTMF Any-Character-Triggered Macro (default) ; LiTZ (Long Tone Zero) ; MPW 63 0206 0 * ; DTMF Long Tones Enable (disabled, default) ; MPW 09 1203 30 * ; DTMF Long Tones Timer, 3.0 Seconds (default) ; MPW 26 02xx * ; DTMF Long Tone Macro (184-199) ; MPW 26 0200 * ; DTMF Any Long Tones Macro ; Command Responses ; MPW 63 0200 1 * ; DTMF Enable/Disable Command Responses (enabled, default) ; MPW 63 0201 1 * ; DTMF Enable/Disable OK Command Responses (enabled, default) ; MPW 63 0202 1 * ; DTMF Enable/Disable Error Command Responses (enabled, default) ; MPW 63 0218 0 * ; DTMF Enable/Disable Macro Command Responses (disabled, default) ;---------------------------------- ; Receiver, Chapter 10 ;---------------------------------- ; ; Receiver configuration is specific to this port's receiver input. ; This configuration is common to all Paths enabled from this Receiver. ; Receiver Timing ; MPW 09 0212 0 * ; COR Filter Delay, 0.00 Seconds (default) ; MPW 09 0213 0 * ; CTCSS Filter Delay, 0.00 Seconds (default) ; MPW 09 0218 0 * ; Flutter Filter Delay, 0.00 Seconds (default) ; Anti-Kerchunker ; MPW 63 0210 0 * ; Anti-Kerchunk Enable (disabled, default) ; MPW 09 0209 100 * ; Anti-Kerchunk Keyup Delay, 1.00 Second (default) ; MPW 09 2209 100 * ; Anti-Kerchunk Re-Arm Delay, 60 Seconds (default) ; MPW 63 0211 0 * ; Anti-Kerchunk No-Hangtime Mode Enable (disabled, default) ; If you're using the Audio Delay, the Audio Gate Delay should be set to the ; same delay time. This eliminates receiver noise stored in the audio delay hardware. ; Once you try it, you can adjust this value to eliminate all keyup noise. ; MPW 09 0217 0 * ; Audio Gate Delay, 0.00 Seconds (default) ; COR and CTCSS Logic Input Macros ; MPW 26 0215 * ; COR Hi-to-Lo Transition Macro ; MPW 26 0216 * ; COR Lo-to-Hi Transition Macro ; MPW 26 0217 * ; CTCSS Hi-to-Lo Transition Macro ; MPW 26 0218 * ; CTCSS Lo-to-Hi Transition Macro ; COR Pulse-Triggered Macros ; MPW 26 02xx * ; COR Pulse-Triggered Macro for x Pulses (171-179) ; MPW 09 0210 25 * ; COR PTM Minimum Pulse Duration, 0.25 seconds (default) ; MPW 09 0211 200 * ; COR PTM Maximum Gap Duration, 2.00 seconds (default) ; Logic Inputs, Chapter 14 ; MPW 26 0215 * ; COR 2 Hi-to-Lo-Triggered Macro ; MPW 26 0216 * ; COR 2 Lo-to-Hi-Triggered Macro ; MPW 26 0217 * ; CTCSS 2 Hi-to-Lo-Triggered Macro ; MPW 26 0218 * ; CTCSS 2 Lo-to-Hi-Triggered Macro ;---------------------------------- ; Transmitter, Chapter 11 ;---------------------------------- ; ; Sample Use Case: Repeater Transmitter with Hangtime ; ; Transmitter configuration is specific to this port's transmitter output. ; This configuration is common to all Paths enabled to this Transmitter. ; Message Delay ; MPW 09 0203 25 * ; Transmitter Turn-On Message Delay, 0.25 second (default) ; Tail Timing ; LinkWired: we want the link to drop immediately when all paths are inactive. MPW 09 0200 0 * ; Courtesy Delay, 0 Second MPW 09 0201 0 * ; Dropout Delay, 0 Second Tail MPW 09 2211 0 * ; Dropout Message Time, 0 Seconds (default) MPW 09 0202 0 * ; PTT Minimum Unkey Delay, 0 Second ; RX Path Priority to TX1 ; Adjust this setting to handle special access priority cases ; MPW 90 2 * ; Mix Audio from all enabled Paths (default) ; Tail Messages and Macros ; MPW 26 0219 * ; Courtesy Delay Violation Macro ; MPW 31 0212 * ; Dropout Message ; MPW 26 0204 * ; Dropout Macro ; MPW 26 0205 * ; PTT Inactive-to-Active Macro ; MPW 26 0206 * ; PTT Active-to-Inactive Before Unkey Delay Macro ; MPW 26 0207 * ; PTT Active-to-Inactive After Unkey Delay Macro ; MPW 26 0202 * ; Any-Path-Active-To-TX Macro ; MPW 26 0203 * ; All-Paths-Inactive-To-TX Macro ; Transmitter Activity Counter/Timer/Macro ; MPW 26 0246 * ; Start-of-Activity Macro ; MPW 26 0254 * ; End-of-Activity Macro ; MPW 45 0201 0 * ; End-of-Activity Counter (default) ; MPW 09 2203 60 * ; End-of-Activity Timer (default) ; TX1 Miscellaneous Configuration ; MPW 63 0212 1 * ; PTT Enable (default) ; MPW 63 0213 1 * ; Key Transmitter Untimed (example) ; MPW 09 2208 0 * ; Key Transmitter Timed (example) ;---------------------------------- ; Identifier, Chapter 12 ;---------------------------------- ; ; Sample Use Case: Wired Link does not have an Identifier ; Transmitter Identifier configuration is specific to this port's transmitter output. ; ; Note: a longer Identifier Pending Interval minimizes playing ID messages over users. ; Set the Identifier Interval to zero to disable the Identifier. ; LinkWired: we don't need an Identifier on a wired link MPW 09 2206 0 * ; Identifier Interval, 0 seconds, disabled ; MPW 09 2207 30 * ; Identifier Pending Interval, 0.5 minutes (default) ; Initial ID Message: Example: Speak "I D Repeater" ; MPW 31 0209 9960 0053 0048 0342 * ; Plays on initial keyup ; Normal ID Message: Example: CW "ID/R" ; MPW 31 0210 9900 18 13 38 27 * ; Plays during a conversation ; Other Optional ID Messages and Macros ; MPW 31 0211 * ; Impolite ID Message ; MPW 26 0208 * ; Initial ID-Triggered Macro ; MPW 26 0209 * ; Polite ID-Triggered Macro ; MPW 26 0210 * ; Impolite ID-Triggered Macro ; MPW 50 02 * ; Initial ID Tail Message ; MPW 50 03 * ; Normal ID Tail Message ; End: Wired Link Identifier Configuration ;---------------------------------- ; CTCSS Encoder, Chapter 13 ;---------------------------------- ; ; Sample Use Case: Repeater Transmitter with Hangtime ; ; Transmitter CTCSS Encoder configuration is specific to this port's ; transmitter output. ; ; LinkWired: CTCSS Encoder Disabled MPW 02 2 0 0 * ; CTCSS Encoder Mode ; For 7330-generated CTCSS tones, set the generated frequency ; MPW 03 2 26 * ; CTCSS Encoder Frequency, 100Hz (default) ; For externally-generated CTCSS tones, the CTCSS Logic Output can be ; used to mute an the external tone generator. For this to work, change ; J38 to the LOGIC position. ; MPW 63 0217 1 * ; CTCSS Controls CTCSS Logic Output Enable (default) ; CTCSS On Time, not required for the example in Mode 1 ; MPW 09 0215 100 * ; CTCSS Encoder ON Time, 1.00 second (default) ; CTCSS Encoder-Triggered Macros, not required for the example ; MPW 26 0211 * ; CTCSS Encoder Inactive-to-Active Macro ; MPW 26 0212 * ; CTCSS Encoder Active-to-Inactive Macro ;---------------------------------- ; Path 22: RX2 to TX2, Chapter 9 ;---------------------------------- ; ; Sample Use Case: a Wired Link ; ; This Path configuration is specific to this Receiver-to-Transmitter Path. ; ; Path Enable ; LinkWired: Path Disabled, not a repeater MPW 63 0242 0 * ; Path Disabled (enabled, default) ; Path Access Mode ; MPW 57 22 1 * ; Carrier Access (default) ; DTMF Decoder Mute ; MPW 63 0252 1 * ; DTMF Mute Enable (enabled, default) ; Timeout Timer ; MPW 63 0262 1 * ; Timeout Timer Enable (enabled, default) ; MPW 09 2201 180 * ; Timeout 3.0 minutes (default) ; MPW 09 1201 50 * ; Timeout Penalty 5.0 seconds (default) ; Timeout Messages ; MPW 31 0204 9960 0339 0003 1487 * ; TO Message, Say "Receiver 2 Timeout" ; MPW 31 0207 9960 1487 0360 0005 0101 *; End TO Message, Say "Timeout Timer 3 Minutes" ; Timeout Macros ; MPW 26 0231 * ; Timeout Macro ; MPW 26 0239 * ; Timeout-End Macro ; Courtesy Message and Macro ; MPW 31 0201 * ; Courtesy Message (default) ; MPW 26 0223 * ; Courtesy Macro ; Path Activity Counter/Timer/Macro ; MPW 26 0247 * ; Start-of-Activity Macro ; MPW 26 0255 * ; End-of-Activity Macro ; MPW 45 0202 0 * ; End-of-Activity Counter (default) ; MPW 09 2204 60 * ; End-of-Activity Timer (default) ;---------------------------------- ; Path 12: RX1 to TX2, Chapter 9 ;---------------------------------- ; ; Use Case: Receiver #1 to Wired Link "Transmitter" Output ; ; This Path configuration is specific to this Receiver-to-Transmitter Path. ; ; QUICKSTART -- you will need to define the Access Mode for the Receiver #1 ; to Transmitter #2 Path. This sample script disables this path. ; Be sure to change the access mode in the control macro below. ; ; Path Enable MPW 63 0241 0 * ; Path Disabled (enabled, default) ; Path Access Mode ; MPW 57 12 1 * ; Carrier Access (default) ; DTMF Decoder Mute ; MPW 63 0251 1 * ; DTMF Mute Enable (enabled, default) ; Timeout Timer ; MPW 63 0261 1 * ; Timeout Timer Enable (enabled, default) ; MPW 09 2200 180 * ; Timeout 3.0 minutes (default) ; MPW 09 1200 50 * ; Timeout Penalty 5.0 seconds (default) ; Timeout Messages MPW 31 0203 9960 0339 0001 1487 * ; TO Message, Say "Receiver 1 Timeout" MPW 31 0206 9960 1487 0360 0005 0101 * ; End TO Message, Say "Timeout Timer 3 Minutes" ; Timeout Macros ; MPW 26 0230 * ; Timeout Macro ; MPW 26 0238 * ; Timeout-End Macro ; QUICKSTART -- you can define a different Courtesy Message for the Receiver #1 ; to Transmitter #2 Path. The default is a unique beep. See page 9-25. ; ; Courtesy Message ; MPW 31 0200 * ; Courtesy Message (default) ; MPW 26 0222 * ; Courtesy Macro ; Path Activity Counter/Timer/Macro ; MPW 26 0246 * ; Start-of-Activity Macro ; MPW 26 0254 * ; End-of-Activity Macro ; MPW 45 0201 0 * ; End-of-Activity Counter (default) ; MPW 09 2203 60 * ; End-of-Activity Timer (default) ;---------------------------------- ; Path 32: RX3 to TX2, Chapter 9 ;---------------------------------- ; ; Use Case: Receiver #3 to Wired Link "Transmitter" Output ; This Path configuration is specific to this Receiver-to-Transmitter Path. ; ; QUICKSTART -- you will need to define the Access Mode for the Receiver #3 ; to Transmitter #2 Path. This sample script disables this path. ; Be sure to change the access mode in the control macro below. ; ; Path Enable MPW 63 0243 0 * ; Path Disabled (enabled, default) ; Path Access Mode ; MPW 57 32 1 * ; Carrier Access (default) ; DTMF Decoder Mute ; MPW 63 0253 1 * ; DTMF Mute Enable (enabled, default) ; Timeout Timer ; MPW 63 0263 1 * ; Timeout Timer Enable (enabled, default) ; MPW 09 2202 180 * ; Timeout 3.0 minutes (default) ; MPW 09 1202 50 * ; Timeout Penalty 5.0 seconds (default) ; Timeout Messages MPW 31 0105 9960 0339 0005 1487 * ; TO Message, Say "Receiver 3 Timeout" MPW 31 0108 9960 1487 0360 0005 0101 * ; End TO Message, Say "Timeout Timer 3 Minutes" ; Timeout Macros ; MPW 26 0232 * ; Timeout Macro ; MPW 26 0240 * ; Timeout-End Macro ; QUICKSTART -- you can define a different Courtesy Message for the Receiver #3 ; to Transmitter #2 Path. The default is a unique beep. See page 9-25. ; ; Courtesy Message ; MPW 31 0202 * ; Courtesy Message (default) ; MPW 26 0224 * ; Courtesy Macro ; Path Activity Counter/Timer/Macro ; MPW 26 0248 * ; Start-of-Activity Macro ; MPW 26 0256 * ; End-of-Activity Macro ; MPW 45 0203 0 * ; End-of-Activity Counter (default) ; MPW 09 2205 60 * ; End-of-Activity Timer (default)